bending analysis的例句大全

The paper also gives the feasibility analysis of asymmetric plate bending under one time feeding cond.

扼要介绍了三轴不对称卷板时,根据被卷钢材的几何参数、力学参数来计算卷制工艺参数.

SEM analysis indicated that evenly distributed fine crystal grain was the reason of good bending strength.

SEM分析认为:造成材料抗弯强度增加缓慢或下降的原因是材料晶粒粗大,晶粒分布不均匀.

The complex modal analysis is developed to investigate bending vibration of a viscoelastic beam.

发展复模态分析研究黏弹性梁的弯曲振动.

It can be used for the analysis of natural bending vibration of step shafts in engineering.

该法亦可用于工程中阶梯梁弯曲固有振动分析.

Approximate Analysis for Bending and Vibration of Laminates

层合板弯曲与振动的近似计算

Technological Analysis and Die Design of Bending Forming for Aliform Parts

翼片弯曲成形工艺分析及模具设计

Theoretical analysis of bending and toppling deformation in slopes of mica quartz schist

云母石英片岩斜坡弯曲倾倒变形的理论分析

As the bending strength of sodium silicate sand cured by ester method is much higher than that cured by CO_2 method the analysis shows that the key point is the refinement of grains of silicate gel.

分析了酯法比CO2法水玻璃砂强度高的原因，指出充分发挥水玻璃粘结效率的关键在于细化水玻璃凝胶胶位。

The mechanical analysis on axial bending of pump barrel

有杆泵泵筒的纵向弯曲机理分析

Analysis on Hot Coilbox Bending Roll Control

热卷箱弯曲辊控制浅析

The Analysis of the Shear Strength of Reinforced Concrete Restrained Members under Biaxial Bending

钢筋砼双向受弯约束梁抗剪强度的试验研究

Measurement and Analysis of Dynamic Bending Strain in Marine Shafting

船舶轴系动态弯曲应变的测量与分析

FEM Analysis of Effect of Bending Force on the Crown of Strip

弯辊力对带钢凸度影响的有限元分析

Analysis and modification of hydraulic roller bending force control system

热轧机组液压弯辊力控制系统特性分析与改进

According to the law of crack development and mechanical index correlation analysis results, use the maximum bending force, shearing force and fracture energy as the main mechanical parameters, put forward the test design method.

基于裂缝动态发展规律与力学指标关联度分析结果，以最大弯曲力、层间剪切力和断裂能作为主要设计参数指标，提出配合比设计的试验方法。

Strain Damage Failure Analysis and Prediction for Beams under Pure Bending Loads

纯弯曲梁的应变损伤失效分析和预测

A Stress Analysis of Damage Concrete Beams Under Pure Bending

损伤混凝土梁弯曲应力分析

It firstly derivates theoretical analysis formula of force and stroke by using beam bending theory and energy method.

首次采用梁的弯曲理论和能量法结合的方法推导了弯曲力和行程的理论解析公式。

Analysis of springback factors for U-bending hot-rolled metal sheet parts

热轧钢U形件弯曲回弹影响因素的分析

Bending and Torsion Analysis of Thin Wall Curved Bar with Closed Cross Section

闭口薄壁曲杆的弯扭分析